{{ app.busy }}
{{ snackbar.icon }}

Enter a hex prefix (1-8 characters) for your public key. Uses {{ vanity.cores }} CPU cores.

warning Prefixes starting with "00" or "FF" are reserved by MeshCore.
Prefix {{ vanity.prefix.toLowerCase() }}...
Expected attempts {{ (Math.pow(16, vanity.prefix.length)).toLocaleString() }}
Estimated time {{ vanity.estimatedTime }}

Searching for public key starting with {{ vanity.prefix.toLowerCase() }}...

Attempts {{ vanity.attempts.toLocaleString() }}
Elapsed {{ vanity.elapsed }}
Speed {{ vanity.keysPerSec }} keys/sec
check_circle Found a match in {{ vanity.attempts.toLocaleString() }} attempts ({{ vanity.elapsed }})
warning Applying this key changes the device identity. A reboot is required.
{{ entry.text }}
{{ regionLoadMode ? 'region>' : '>' }}  {{ consoleSuggestion }}
Reading stats...
error {{ stats.error }}
{{ row.label }}
{{ line }}
Info & Actions
Name & Location
Max length is 24 bytes with location set, 32 otherwise. Emoji and unicode may take more than one byte.
Access
Sets a new admin password. Any node using this password will be added to the admin ACL list.
Default: "password".
Sets/updates the guest password. Leaving this empty is recommended, as it gives users access to owner info and neighbors functionality.
Room server settings
Radio settings
Slovenia community preset
869.618 MHz · 62.5 kHz · SF8 · CR8 · 22 dBm · 10% duty cycle, plus the published repeater routing and advertising recommendations.

Suggested radio settings per region.

These radio settings have been suggested by the community.

Power level of the LoRa chip (1-22 dBm). Some boards have an additional amplifier. Setting too high may violate local regulations.

After each transmission, the repeater enforces a silent period proportional to the on-air time. You are responsible for choosing a value appropriate for your jurisdiction (e.g. EU 868 MHz requires 10% duty cycle).

Airtime factor (AF): {{ app.device.vars.af }}
Default: 1 (~50%)

Advertising
Zero-hop advert interval in minutes, rounded to nearest multiple of 2 (60-240, or 0 to disable).
Default: 0
Flood advert interval in hours (3-168, or 0 to disable).
Default: 47 (repeater), 0 (sensor)
Maximum flood hop count (0-64).
Default: 64
Maximum hop count for flood packets that carry no region scope (0-64).
Requires firmware 1.16+
Maximum hop count for flooded adverts (0-64).
Default: 16. Requires firmware 1.16+
Access control
info No nodes in the access list yet.
Regions
warning The device's reply buffer is full, so this region list is incomplete. Editing is disabled to avoid deleting regions that are not shown here. Use the console (region) to inspect the full tree.
Owner info
Advanced settings

Rejects flood packets that appear to be in a loop.
Default: off. Requires firmware 1.14+

Minimal: drops if own hash appears 4+ times (1-byte) or 2+ (2-byte). Moderate: 2+ (1-byte) or 1+ (2-byte). Strict: 1+ for all sizes.

Sets the ID/hash encoding size used in adverts.
Default: 0. Requires firmware 1.14+

0: 1-byte (256 IDs, max 64 flood). 1: 2-byte (65K IDs, max 32 flood). 2: 3-byte (16M IDs, max 21 flood).

Older firmware (<1.14) will drop packets with multi-byte hashes.

Local interference threshold.
Default: 0
AGC reset interval in seconds, rounded down to a multiple of 4.
Default: 0
Site-position presets from the Colorado MeshCore repeater guide. This only changes RX delay, TX delay, and Direct TX delay.
[Experimental] Processing delay for received traffic (0-20).
Default: 0
Retransmit delay factor for flood traffic (0-3).
Default: 0.5
Retransmit delay factor for direct traffic (0-3).
Default: 0.2
Battery voltage divider calibration. 0 uses the board default.
info You have unsaved changes